How To Reset My Dyson Vacuum

If your Dyson vacuum is not working correctly, you might wonder where to find the reset button to troubleshoot the problem.

Unfortunately, Dyson vacuums don’t have a reset button. If so, then how do you reset a Dyson vacuum cleaner?

This article explains some common problems that can affect a Dyson vacuum’s operation and outlines the steps to resetting it.

5 Ways To Reset a Dyson Vacuum

When resetting the Dyson vacuum, turn off the cleaner and remove the power cord from the electrical outlet. With a screwdriver, you can access the trouble area and reset it.

Below are five common faults that may arise on your Dyson vacuum and how to troubleshoot it.

Method #1: Resetting the Brush

If your Dyson vacuum cleaner isn’t working correctly, and you notice the brush bar is not spinning, it is because it is probably clogged. Items like hair and debris are the common culprit that can clog the brush bar.

In this case, to reset the brush, you have to remove it and free the clog.

Here’s how to reset a Dyson vacuum brush:

1. Check if the vacuum is locked in an upright position; if not, then disengage the brush bar.
2. Disassemble the cleaner handle.
3. Examine the cleaner’s head angle if it is too low to allow the brush bar to spin.
4. Make suitable adjustments to the cleaner head such that it spins freely.
5. Assemble the cleaner and test it.

Method #2: Resetting the Filter

Your Dyson vacuum cleaner filter needs to be cleaned periodically. If you don’t clean the filter, it will become clogged, affecting the cleaner’s suction capacity.

According to Dyson, you should clean the filter at least once every month to keep the machine functioning efficiently.

Here’s how to reset a Dyson vacuum filter:

1. Remove the filter from the cleaner.
2. Gently tap on the filter on the side of a bin or sink to remove loose dust and debris.
3. Rinse the filter under cold tap water, gently rubbing your hands on it.
4. Fill the filter with warm tap water, cover the open end with your hand, and give it a firm shake.
5. Repeat step 4 until the water runs clear from the filter.
6. Leave the filter in a ventilated area to air dry.
7. When dry, install the filter in the cleaner and plug it back on.

Method #3: Resetting the Battery

Dyson vacuum cleaners are designed such that they are constantly charging. As such, anytime you need to use them, there will always be power in them.

But when you find that it no longer holds a charge for long, or it’s not charging altogether, it’s probably because the battery is faulty.

Storing your vacuum cleaner with batteries in hot environments at over 18 to 28 degrees celsius deteriorates the battery faster.

Here’s how to reset the battery of a Dyson vacuum:

1. Take the battery out of the cleaner and replace it.
2. Plug the vacuum into a wall outlet and start it up again.
3. If the cleaner does not hold a charge, unplug it from the outlet again.
4. Pull and hold the trigger for 20 seconds.
5. Plug the cleaner into the outlet again and start the charging.
6. If it still does not work, you must replace the battery.
7. Note that Dyson vacuum cleaners’ batteries come with a 2-year warranty.

Method #4: Resetting the Motherboard

Many Dyson vacuum cleaners make use of a digital suction motor that is controlled by a motherboard.

This design is often found in Dyson cordless cleaners. The motherboard is responsible for managing the function of the cleaner and ensuring its components are powered correctly.

Like most electronic appliances, the motherboard in the Dyson vacuum cleaner can also suffer from issues.

Here’s how to reset a Dyson vacuum motherboard:

1. Please remove the battery from the Dyson vacuum or disconnect it from the electrical outlet.
2. Let the vacuum cleaner stay without a power source for at least 5 minutes.
3. After the electrical charge in the motherboard has been dissipated, reconnect it to a power source and power it on.

Method #5: Resetting the Motor

Another common malfunction you may experience with your Dyson vacuum cleaner is with its motor. Sometimes, the motor might pulsate when you use it.

When the motor turns on and off repeatedly instead of continuously when you use it, you wouldn’t get a continuous suction and hence, wouldn’t clean properly. This issue could be due to a blockage somewhere in the unit.

As the vacuum senses a blockage that causes a lack of airflow, it pulses the motor to prevent it from overheating.

Here’s how to reset a Dyson vacuum motor:

1. Remove its detachable parts like the hose, cleaning head, wand, and everything else.
2. Clean the blockage in those parts you removed.
3. Clean the electric connector carrying power before connecting the detachable.
4. Reattach all the parts that you removed earlier.

Conclusion

As you can see from this guide, it’s easy to troubleshoot your Dyson vacuum cleaner. While it may lack a reset button, once you can identify the issue with your cleaner, you should be able to troubleshoot it quickly.